cookies
Du vil finde vores "cookies" lækre
Cookies på Muzikers hjemmeside bruges til at gøre hvert af dine besøg hos os til en behagelig oplevelse. Accepter brugen af ​​alle cookies ved at klikke på knappen "Jeg accepterer", eller vælg kun dem du ønsker i indstillingerne. Mere information
Jeg accepterer
Afvis
Tilbud

Alctron MA614B Stativ til bordmikrofon

3,75
Broadcasting microphone stand with aluminum construction from the MA series. Offers half elliptic aluminum tube wich gives enough space to collect the cable (cable not included) along with the stand, strong tension springs to support the heaviest...
På lager 19 stk.
Sendes d. 29.04.2024 ,
2024-05-03
Stativ til bordmikrofon Alctron MA614B Stativ til bordmikrofon

Alctron MA614B Stativ til bordmikrofon

397 kr
405 kr

Produktkode: MA614B | ID: 224795

Alctron MA614B Stativ til bordmikrofon

Broadcasting microphone stand with aluminum construction from the MA series. Offers half elliptic aluminum tube wich gives enough space to collect the cable (cable not included) along with the stand, strong tension springs to support the heaviest studio microphones and locking center hinge that assures microphone stability. Features long 5/8 x 27 mm that fits all types of mounts. Product comes in Black finish.

Parametre og specifikationer

Egnethed

Ansøgning


Land

Lavet i

Kina


Anbefalet tilbehør

Samlet bedømmelse baseret på 14 brugeranmeldelser:

3,75

Radim Axel V.

Helhedsindtryk

Dato
12.12.2022

Velmi stabilní

Maurizio A.

Helhedsindtryk

Dato
02.02.2022

Ottimo supporto ad un prezzo ragionevole

Stan C.

Helhedsindtryk

Dato
22.05.2020

Disappointing. Pros: - Clean Aesthetics - Has a built-in, internally routed XLR mic cable - Can support heavy mics / setups (with caveats, see below) Cons: - Surprisingly heavy / hard to work with. I expected smooth adjustment, but this is the opposite: you can get your daily workout just trying to adjust it. Because the spring tension is so high, you need to have the nuts on its joints locked at any time and you really need to tighten these until your hand hurts. This then makes on-the-fly adjustments impossible, you are fighting it at all times. As a consequence: - The base clamp is too weak for the stand's weight and stiffness and gets easily dislodged, even if you tighten it up until it hurts. It doesn't help that it has a felt pad on the inside - this slips easily on smooth surfaces. I replaced it with silicone pads on both sides, otherwise the stand is nearly unusable and dangerous. The clamp has arm holes that would normally allow you to attach it on both horizontal and vertical surfaces, but the hole for vertical setup is way too close to the surface you are clamping to - and that doesn't allow the chunky base of the arm to fit. This is compounded by the base joint having a very limited adjustment angle. - The mic head does not turn at all. Not sure if it's jammed on mine, or bad design. So you can't rotate the mic once attached, unless you partially unscrew the mic. - I chose this over desk stands that have springs on the outside to avoid unwanted noise/resonance. Sadly, the joints are loose and rattle unless tightened, so do the metallic inserts. It luckily doesn't rattle when fully tightened, but as mentioned this completely eliminates any adjustments. My advice, save your money and look elsewhere.

Dominik K.

Helhedsindtryk

Dato
15.05.2020

Ennyi pénzért jobbat vártam. A beépített kábel semmit sem ér, szinte kiesik a mikrofonból, az állványt lehetetlen asztalhoz erősíteni, minden egyes alkalommal, amikor forgatni szeretném az állványt lecsúszik róla, ami az állványhoz volt ragasztva, az 10 perc alatt le is esett róla, a mikrofontartó felszerelés után nem forgatható, ezért csak reménykedni lehet, hogy sikerül megfelelő szögben feltenni. Az ellenségemnek sem ajánlanám.

Pascal S.

Helhedsindtryk

Dato
05.05.2020

Hab den Mikrofonarm seit heute. Hab ihn direkt aufgebaut und direkt gemerkt wie massiv er im Gegensatz zu den billo Mikrofonarmen von Amazon ist, aber gut die Kosten auch 20€ weniger. Bisher hält er mein Rode Podcaster + Spinne ohne Probleme.